A Step-by-Step Overview to Installing a Bath Tub
A Step-by-Step Overview to Installing a Bath Tub
Blog Article
They are making a few good observations regarding A Step-by-Step Guide to Installing a Bathtub in general in this great article which follows.
Setting up a bathtub isn't exactly rocket science, but it does call for strong plumbing, carpentry, and occasionally, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a moderately difficult task. If the old bathtub is easily accessible, the task can move speedily; if you need to open up a wall to remove the old bathtub as well as position the brand-new bathtub, the job is much harder. In either instance, the project is within a residence handyman's skills, although you will certainly need an assistant to leave the old bathtub as well as embeded in the new one. Ensure you have certified yourself for the work as well as are comfortable trying it. Instead of working with a specialist to take over a halfway-completed task, it is much better to take into consideration utilizing one prior to you begin. Opportunities are you may need an expert plumber to make tube connections.
This write-up will aid you set up a brand-new bathtub in your washroom if you have actually already purchased a brand-new tub and don't require to change the setup of your previous supply of water pipelines.
Your devices as well as product checklist need to comprise the following:
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your setup, after that the first thing you ought to do is separate the water supply. After doing so, switch on the taps to drain any kind of water remaining in the system. The process of eliminating the existing faucets can be quite troublesome as a result of the restricted gain access to that is typically the instance.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a cloth prepared for the staying water that will certainly come from the pipes. When the supply pipelines have been eliminated, utilize the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single faucets from transforming throughout this process. When the faucets have actually been gotten rid of, the holes in the bath/basin will have to be cleaned up of any kind of old securing compound.
Before proceeding to fit the brand-new faucets, contrast the pipeline connections on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic port to stop damages to the string. One end of the adapter fits on the plastic tail of the tap and the other end offers a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will require reducing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, position the tap in the mounting opening in the bath/basin making certain that the washing machines are in place in between the faucet as well as the sink. Protect the tap in position with the maker supplied backnut. When the tap is securely in position, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with typical tap adapters. The previous kind must be linked to the tap ends first, tightening up only by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Setting up the Bathtub
Using both wood boards under its feet, put the tub in the required position. The wood boards are valuable in uniformly spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto 4 little points.
The following goal is to ensure that the bath tub is leveled all round. This can be attained by checking the spirit level and also changing the feet on the bathtub until the level reviews level.
To install faucets, fit all-time low of the outermost versatile faucet port to the appropriate supply pipeline by making a compression join; then do the exact same for the other faucet.
Switch on the water supply and also check all joints and also new pipework for leakages as well as tighten them if necessary. Fill the bathtub as well as also inspect the overflow outlet and also the typical outlet for leakages.
Lastly, take care of the bath paneling as described in the supplier's instruction manual. Tiling and also sealing around the bath tub must wait until the bath tub has been utilized at least once as this will certainly settle it right into its last setting.
Planning for the Installation
To start with, the sustaining frame supplied with the bathroom ought to be fitted (if needed) according to the supplier's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is essential to make certain that if the faucet comes with a plastic washer, it is fitted in between the bathroom and also the taps. On a plastic bath, it is additionally reasonable to fit a supporting plate under the taps device to prevent strain on the tub.
Fit the adaptable tap connectors to the bottom of both taps utilizing 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you make use of every one of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath should currently be ready to be suited its final placement.
Tiling Around the Tub
In the area where the bathroom meets the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the installation can relocate sufficient to break an inflexible seal, triggering the water to penetrate the wall surface between the bathroom and the tiling, causing problems with wetness as well as feasible leaks to the ceiling below.
You can pick from a range of coloured sealers to blend in your components and installations. They are sold in tubes as well as cartridges, and can securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with spins of soaked paper or soft rope. Remember to always fill up the bath tub with water before securing, to allow for the motion experienced when the bathtub is in usage. The sealer can break rather early if you do not think about this motion prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are additionally easily offered on the marketplace. It is advisable to fit the ceramic tiles making use of water-resistant or water resistant sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm just very eager about How to Install a Bathtub Yourself and I really hope you appreciated the entire post. Please set aside a second to share this entry if you enjoyed it. Bless you for your time. Kindly come by our website back soon.
Recurring Service Plans
Report this page